The EverMetal Process
Close

We will be exhibiting at the Chicago Roofing Contractors Association Trade Show on January 18-20. Visit us or Schedule an Appointment HERE!

We will be exhibiting at the SprayFoam Convention & Expo on February 12-15. Visit us or Schedule an Appointment HERE!

We will be exhibiting at the IIBEC International Convention & Trade Show on March 3-6. Visit us or Schedule an Appointment HERE!

We will be exhibiting at the International Roofing Expo on March 7-9. Visit us or Schedule an Appointment HERE!

Call Us

800-575-8966

The EverMetal Process

Replacing a metal roof can be expensive, time consuming and cost your business precious down time. Using the EverMetal system when restoring your metal roof provides the perfect alternative to keep your company moving forward at a fraction of the cost. The EverMetal system is simple, easy, and cost effective:

  • Step 1: Power wash and prep roof
    • All roofs need to be washed with a 3500 PSI power washer to clear any debris and dirt off the roof.
    • After the roof is cleaned and dry, an inspection of the roof is made to see what repairs may need to be made.
    • All details and flashings are inspected to make sure that they are functioning properly.
  • Step 2: Add primer
    • If there is any rust on the roof, there is a primer that is sprayed or rolled on those areas.
    • Primer is only needed where rust is present.
  • Step 3: Add Everseal sealant on all seams, fasteners, and penetrations
    • Everseal is a thick mastic sealant that is applied to fasteners, roof penetrations, and all seams where the metal overlaps horizontally and vertically.
    • Our Everseal sealant sticks to almost every surface allowing the team to be efficient, reliable, and consistent.
    • Its fast-drying time and ability to adhere even under water allows increased productivity and a quicker way to finish the project.
  • Step 4: Base coat after the Everseal is set up and dried
    • A base coat is applied to the entire roof that is either sprayed or rolled at an application rate of one and a quarter to one and a half gallons per 100 square feet.
  • Step 5: Top coat
    • The final top coat provides a long lasting coat that will extend the durability and life of the repaired roof.
    • This final process is either sprayed or rolled at an application rate of one and a quarter to one and a half gallons per 100 square feet.
Previous Article Tech Tip: How to tell if leftover material is still good?
Next Article Evercoat OnePass
Vista Plaza at the Parkway

Vista Plaza at the Parkway

Houston, TX
Sacramento Retail Center

Sacramento Retail Center

Sacramento, CA
Houston Methodist West Hospital

Houston Methodist West Hospital

Houston, TX
Rialto Police Department

Rialto Police Department

Rialto, CA
Rolling Plains Correctional Facility

Rolling Plains Correctional Facility

Haskell, TX
EPDM Substrate Repair

EPDM Substrate Repair

Wentzville, MO
Camden County Library

Camden County Library

Camdenton, MO
Jorgensen Steel

Jorgensen Steel

Dallas, TX
Metal Roof Restoration

Metal Roof Restoration

Aurora, CO
Monroe Civic Center

Monroe Civic Center

Monroe, LA
Sunnyvale Tech Company

Sunnyvale Tech Company

Sunnyvale, CA

Featured Products

- view all products -
Everseal

Everseal

All-purpose, high performance, moisture cure, self-leveling siliconized urethane hybrid roof sealant for general maintenance and roof repair (fabric not required). Available in 10.3oz & 28oz tubes, 2 gallon & 5 gallon pails.

Silkoxy H3

Silkoxy H3

A high-solids, single component, no mix, moisture cured fluid applied silicone roof coating. Designed as a protective coating for most roof membranes. No primer needed in most applications.

Evercell 2.0

Evercell 2.0

Evercell Spray Foam 2.0 (245fa) is a two component, closed-cell spray applied polyurethane wall foam system. Evercell Spray Foam offers high compressive strengths, smooth aesthetics and a broad application temperature window. Evercell Spray Foam is available in Summer, Winter and Fall ranges.

Opticell 2.0

Opticell 2.0

Opticell Spray Foam 2.0 (HFO) is a two component, closed-cell spray applied polyurethane wall foam system. Opticell Spray Foam offers high compressive strengths, smooth aesthetics and a broad application temperature window. Opticell Spray Foam is available in Summer, Winter and Fall ranges.

Copyright © 2023 Everest Systems Co.   |   Admin Login